Sears 113.243311 Manuale Utente

Save This Manual For Future ReferenceSEARSownersmanualMODEL NO. 113.243300SAW ONLYMODEL NO. 113.243311SAW WITH LEGSAND MOTORSerialNumberMode! and seri

ossenibly7, Install the small pulley ontothe motor shaft andtighten the set screw in the pulley hub against the flat part of the mo

14. Route motor cord up and around front leg and along backside of saw frame.Plug motor cord into outlet on upper section of band s

assemblyINSTALLING TABLEApply a coat of automobile wax to the table.L Place the table on the band saw so that the two trunnion pins and the

4. Loosen the two setscrews which lock the upper blade guides and separate them about 1/8".Do that same thing to the lower guides

ossemblyто AVOID BEING SCRAPED SHOULD BLADE SUDDENLY UNCOIL WEAR SAFETY GOGGLES AND CAREFULLY UNCOIL THE BLADE HOLDING IT AT ARMS LENG

NOTE: The upper and lower blade guides support the blade and keep it from twisting during operation. An adjustment is necessary when b

assemblyON-OFF SWITCHWAR N1N G: DO N ‘T CONNECT POWER COR D TO ELECTRICAL OUTLET IN YOUR SHOP UNTIL YOU ARE SURE THAT MOTOR ROTATION IS COR

getting to know your bond saw/sonderFRONTBACKHelp you to become1. ADJUSTMENT DIAGRAMS .familiar with the adjustments.2. TENSION ADJUSTMENT KNOB .

ig. fo, know yoyr band saw/sander9. GUSDS BARWhen the upper guides are raised or lowered, they must not deflect the blade sideways. This mean

6. Attach the sanding platen to the guide bar with the same screw that held the upper blade guide assembly. Do not tighten the screw

full ONE YEAR WARRANTY ON GRAFTSiWAW BAND SAWit within one year from the date of purchase, this Craftsman Band Saw fails due to a defect in materia) o

iisic borid saw/sander operationBASIC BAND SAW/SANDER OPERATIONA hand saw is basically a “curve CLftting" machine. It is not capable o

mainîenanceWARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF” AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRICA

trouble shootingWARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING

TROUBLE SHOOTING - MOTOR {Cont.|TROUBLE PROBABLE CAUSE' ...- ...-----------------remedyMotor starts slowly or fails to come up1. Low volta

CRAFTSMAN 12-INCH BAND SAW/SANDER, MODEL 113.243300 & 113.243311Ja.SEE FIGURE 3 FOREXPLODEDVIEWimmFIGURE 1

Always order by Part Number — not by Key NumberFIGURE 1 PARTS LISTCRAFTSMAN 12-INCH BAND SAW/SANDER, MODEL 113 243300 & 113.243311KEYNO.PARTNO.DES

CRAFTSMAN 12-INCH BAND SAW/SANDER, MdDEI. 113 243300 & 113.243311D.mQm

CRAFTSMAN 12-INCH BAND SAW/SANDER, MODEL 113.243300 & 113.243311FIGURE 2 PARTS LISTKEYPARTKEYPARTMO.WO.DESCRIPTIONNO.NO.DESCRIPTION1STD522503*Scre

craftsman 12-1 iSI BAMD SAW/SAWDER, MODEL 113.243300 & 113.243311FIGURESSUPPLIED WITH^yODEL 113.243311 ONLY|Key i No,Part No.Description162614Leg.

CRAFTSMAN 12-INCH BAND SAW/SANDER. MODEL 113.243300 & 113.243311NOTE;ANY ATTEMPT TO REPAIR THIS MOTOR MAY CREATE A HAZARD UNLESS REPAIR IS DONE BY

additional safety instrycfions for band saw/sanderSafety is a combination of operator common sense and alertness at all times when the band sa

acSditional safety instructions for band saw/sanderWARNING: THE 5" BAND SAW PULLEY AND THE2-1/2" MOTOR PULLEY FURNISHED, WILL RUN THE

motor specifications and eléctrica! requirementsThis machine is designed to use a 1725 RPM motor only. Do not use any motor that runs

unpacking and checking contents ' CONTENTSUNPACKING AND CHECKiNG CONTEOTS ... 6ASSEMBLYAssembling S

THE FOLLOWING PARTS' fWODEL 113,243311 ONLY.ARE INCLUDED WITHItemDescriptionQty.A'Nut, Hex Head 1/2-13...8A *

assemblyMOUNTING BAND SAW/SANDER ON LEG SETNOTE: For illustrative purposes, the Band Saw is shown mounted on the Craftsman Catalog No. 9

HUB SET SCREW4. Place the large pulley onto the drive wheel shaft and insert the key into the keyway of the shaft and pulley. Posi