Sears 358.357182 Manuale Utente Scaricare il pdf (Pagina 18)

• Use only ttie R<Kiuce<j4aeid3aek Guide B*r

specified for your saw in “Specificst'ons."

a. Remove the guide bar to service.

b. Ciean ou Doles at least once for eacn

five Dours of ooeration.

c. Remove sawausi from the guide bar .

groove oenosicaily with a putty knife or

a wire. Rgured<t.

a. Remove burrs by fifing the side edges

of the guide bar grooves square with a

flat file. RgureSS.

TO W[

CORRECT

GUIDE BAR

GROOVE

WORN GROOVES

RILE EDGES'

SQUARE

Figure S5

Restore square edges to an uneven rail

top by filing with a Hat file. Rgure 3S .

B, AIR FILTER

• A dirty air filter:

—redueas cutting power

-o Increeses fuel consumption

• Cfeen the eif filter;

—Freguently, especially under very dusty

cofiditiOftSe

— Always after 10 tanlcs of fuel ntixtuie or 5

hours of opemtion, whichever is less.

iCAUtlONd To avbid creadng a flte hazard, do not

use g3»Iineoranyotherf!amfnable liquid tocfean

thefilter.

1. Clean off the carburetor cover and the area

around it to Keep dirt and sawdust from fall*

ing into the carbu^tor chamber when the

cover is removed.

2. Remove thecarburetor cover screws and car*

buretor cover. Rgtjre36.

3. Pull out the air filter,

4. Wash the filter in soap and water.

NOTE: Be careful when replacing the car

buretor cover as incorrect placement will

prevent the choKe frotn working properly.

9, Move the choke knob a« the vmy to the right,

to. Check the «wia shutter to be sure it is closed.

Figures 36&43.

11. Reinstall the carburetor cover and tighten

the cartJUteter cover screvss.

12. Check aie operation of the choke.

NOTE If the choke knob sticks or will not

move, remove the cover and repeat steps

11 and 12 above. *

CARfiUREIOR

COVER SCREW

iCAimONaPo not use gasoline or other fiamma^'

bie liquid to clean the flit«’ ^ avokl cmating a Hr«

hazard.

5. Squeejte the filter dry.

6. Add a small amount of oil to coat the filter.

NOTE Avoid soaking the filter with oil.

7. ^ueeze out excess oil.

8. Replace filter by tucking in edges and

smoothing it flush with the eattxiretornous*

RgureSfi

c. SPARK AERESTOR

,1!

• Carbon depotitsbuitdupantheepsiicamstor

as me saw is used and must be removed to avoid

Mumta

cevta H iHSr*

creatingahre hazard or causing engtng damage.

• Replace thesparkanestorifbnajci occur.

sMiw *««f $T0« scasEit _

• №e#pthesparkarre«oreie«iatalftimas.

01 ean*

*~as required

—at least oneehtr each 2SG0 hmin of opecahon

Kerns feqiared: wire brush. 3/8' wrench

1. Ooconnect the spark plug wire.

2. RemovBlheMofflarCover-Figure 37.

3. Rerowe the screen from the baffle.

4. dean the screen with a wire brush or replace f

breaks are iound.

5. Reassemble parts.

IS

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 31 32

Commenti su questo manuale

Nessun commento